Ниже представлена эта же страница в формате, позволяющем производить копирование текста.

KMT STELLRAM - полный каталог инструмента - 2014 год EN

                5315VA                     для размещения заказа - kennametal@kennametal.su
                Technical Information

                Calculation of the average chip thickness in relation with the ae (Radial Engagement) if ae is less than 50% of dia.

Shoulder Mills  Formula: Programme Feed Rate (fz)       hm	 =	Average chip thickness           Formula: Average Chip Thickness (hm)
                                                        ae	 =	Radial engagement
                          fz = hm x    d                fz	 =	Feed per tooth                   hm = fz x  ae
                                       ae               d	 = 	Cutter diameter                             d

                Multiplication factor for the feed rate based on the percentage of radial engagement of the cutter diameter

                ae %      Cutter  25mm    Coefficient  ae %      Cutter  32mm   Coefficient  ae %      Cutter  40mm   Coefficient
                                             Factor                                 Factor                                 Factor
                   5          ae mm                        5          ae mm                       5          ae mm
                   10                          2,30        10                         2,30        10                         2,30
                   15           1,25           1,66        15           1,60          1,66        15           2,00          1,66
                   20           2,50           1,40        20           3,20          1,40        20           4,00          1,40
                   25           3,75           1,25        25           4,80          1,25        25           6,00          1,25
                   35           5.00           1,16        35           6,40          1,16        35           8,00          1,16
                50 - 100        6,25           1,05     50 - 100        8,00          1,05     50 - 100       10,00          1,05
                                8,75           1,00                    11,20          1,00                    14,00          1,00
                           12,50 - 25,00                           16,00 - 32,00                          20,00 - 40,00

                Multiplication factor for the feed rate based on the percentage of radial engagement of the cutter diameter

                ae %      Cutter  50mm    Coefficient  ae %      Cutter  63mm   Coefficient  ae %      Cutter  80mm   Coefficient
                                             Factor                                 Factor                                 Factor
                   5          ae mm                        5          ae mm                       5          ae mm
                   10                          2,30        10                         2,30        10                         2,30
                   15           2,50           1,66        15           3,15          1,66        15           4,00          1,66
                   20           5,00           1,40        20           6,30          1,40        20           8,00          1,40
                   25           7,50           1,25        25           9,45          1,25        25          12,00          1,25
                   35          10,00           1,16        35          12,60          1,16        35          16,00          1,16
                50 - 100       12,50           1,05     50 - 100       15,75          1,05     50 - 100       20,00          1,05
                               17,50           1,00                    22,05          1,00                    28,00          1,00
                           25,00 - 50,00                            31,50- 63,00                          40,00 - 80,00

                Example: 50mm diameter cutter using a 5,0mm radial engagement (ae) = 10% of the cutter diameter. 				
                At 10%, your coefficient is 1,66 (see chart); therefore you must multiply your feed rate by 1,66 for correcting the feed for profiling.

                A194                                                                                      www.kennametal.su

                                                        для заказа - kennametal@kennametal.su
Заявка