для размещения заказа - kennametal@kennametal.su 7700VR06
Milling Inserts & Recommended Feeds
RPEX06-701 RPMT06-41 RPEW06-T
Product Application & Material Dimensions (mm) d s
Roughing Semi-Finishing Finishing
EDP Item Description Grade Depth of Cut (mm) d (IC) l s r hm min
ap max ap min - max ap min - max Contour Mills
-
- 0,50- 1,50 0,10 - ,50
034540 RPEX0602M0F-701 SP6519 - 6,00 - 2,38 3,00 0,02
023313 RPEX0602M0F-701 GH2
034541 RPEX0602M0F-701 SP4019 - 6,00 - 2,38 3,00 0,02
6,00 - 2,38 3,00 0,02
015219 RPMT0602M0E-41 X500 - - 6,00 - 2,38 3,00 0,03
034542 RPMT0602M0E-41 SP6519 - - 6,00 - 2,38 3,00 0,03
023327 RPMT0602M0E-41 MP91M - - 6,00 - 2,38 3,00 0,03
024755 RPEW0602M0T X500 - - 6,00 - 2,38 3,00 0,06
Machining Choice: 1st Choice 2nd Choice 3rd Choice | Material Guide Key descriptions found on page A5.
7700VR06 Feeds fz (mm/tooth)
Geometry
Grade
Operation
Unalloyed
Steel
Alloyed
Steel
Stainless
Steel
Stainless Steel
Refractory PH
Gray
Iron
Spheroidal-
Ductile Iron
Malleable
Iron
Aluminium &
Alloys
<16% Si 116 HBN
Aluminium &
Silicon
>16% Si 92 HBN
HTA Iron
Based Alloys
HTA Cobalt
Based Alloys
HTA Nickel
Based Alloys
HTA Titanium
Based Alloys
Hard Steel
>1400 N/mm2
>415 HBN
Chilled Cast Iron
>1400 N/mm2
>400 HBN
Min. - Max. Min. - Max. Min. - Max. Min. - Max. Min. - Max. Min. - Max. Min. - Max. Min. - Max. Min. - Max. Min. - Max. Min. - Max. Min. - Max. Min. - Max. Min. - Max. Min. - Max.
F-701 SP6519 Contouring 0,02 - 0,10 0,02 - 0,08 0,02 - 0,10 0,02 - 0,08 0,02 - 0,10 0,02 - 0,10 0,02 - 0,07 0,02 - 0,10 0,02 - 0,07 0,02 - 0,05 0,02 - 0,05 0,02 - 0,06 0,02 - 0,07 - -
F-701 GH2 Contouring - - - - - - - 0,02 - 0,10 0,02 - 0,07 - - - - - -
F-701 0,02 - 0,10 0,02 - 0,07 - -
SP4019 Contouring 0,02 - 0,08 0,02 - 0,06 0,02 - 0,08 0,02 - 0,06 0,02 - 0,08 0,02 - 0,08 0,02 - 0,05 0,02 - 0,04 0,02 - 0,04 0,02 - 0,05 0,02 - 0,06
E-41
E-41 X500 Contouring 0,03 - 0,12 0,03 - 0,10 0,03 - 0,12 0,03 - 0,10 0,03 - 0,12 0,03 - 0,12 0,03 - 0,10 - - 0,03 - 0,06 0,03 - 0,05 0,02 - 0,05 0,03 - 0,07 - -
E-41 SP6519 Contouring 0,03 - 0,12 0,03 - 0,10 0,03 - 0,12 0,03 - 0,10 0,03 - 0,12 0,03 - 0,12 0,03 - 0,10 - - 0,03 - 0,06 0,03 - 0,05 0,02 - 0,05 0,03 - 0,07 - -
MP91M Contouring 0,03 - 0,12 0,03 - 0,12 0,03 - 0,10 - ------ -
T - - - -
X500 Contouring 0,10 - 0,13 0,10 - 0,12 - - - - - - - - - - - - -
Note: HTA = High Temperature Alloys
Note: Speed recommendations can be found on page A214.
www.kennametal.su A209
для заказа - kennametal@kennametal.su