KMT STELLRAM - полный каталог инструмента - 2014 год EN
для размещения заказа - kennametal@kennametal.su E_LL4
4 - Flute End Mill
Recommended Feeds Solid Carbide
E_LL4 Feeds fz (mm/tooth) - Slotting / Pocketing General Purpose - End Milling
D Unalloyed Steel
<600 N/mm2
Range <180 HBNMin. -Min. -Min. -Min. -Min. -Min. -Min. -Min. - Min. - Min. - Min. - Min. - Min. - Min. - Min. - Min. - Min. - Min. - Min. -
6,0 Max. Max. Max. Max. Max. Max. Max. Max. Max. Max. Max. Max. Max. Max. Max. Max. Max. Max. Max.
8,0 Unalloyed Steel
10,0 700-950N/mm20,0180,0180,0180,0180,0160,0180,0180,0150,0180,0180,018 - - 0,018 0,013 0,013 0,018 - -
12,0 200-280 HBN0,0330,0330,0330,0300,0270,0300,0270,0240,0340,0300,027 0,034 0,025 0,024 0,033
16,0 Alloyed Steel0,0240,0240,0240,0240,0210,0240,0240,0200,0240,0240,024 - - 0,024 0,018 0,018 0,024 - -
<600 N/mm20,0490,0490,0490,0430,0370,0430,0370,0330,0510,0430,037 0,051 0,036 0,035 0,047
0,030 0,030 0,030 0,030 0,026 0,030 0,030 0,025 0,030 0,030 0,030 - - 0,030 0,023 0,023 0,030 - -
<180 HBN0,0650,0650,0650,0560,0470,0560,0470,0420,0680,0560,047 0,068 0,049 0,046 0,063
Alloyed Steel0,0360,0360,0360,0360,0300,0360,0360,0300,0360,0360,036 - - 0,036 0,029 0,029 0,036 - -
950-1200N/mm20,0820,0820,0820,0700,0570,0700,0570,0510,0870,0700,057 0,087 0,062 0,058 0,079
280-355 HBN0,0480,0480,0480,0480,0390,0480,0480,0400,0480,0480,048 - - 0,048 0,039 0,039 0,048 - -
Alloyed Steel0,1190,1190,1190,0990,0790,0990,0790,0700,1270,0990,079 0,127 0,090 0,084 0,115
1200-1400N/mm2
355-415 HBN
Stainless Steel
Austenitic + Ferretic
300 Series
Stainless Steel
Martensitic
400 Series
Stainless Steel
Refractory PH
Cast Irons
Grey
GG-FT
Cast Irons
Spheroidal- Ductile
GGG-FGS
Cast Irons
Malleable
GTS -MN/MP
Aluminium &
Alloys
<16% Si 116 HBN
Aluminium & Silicon
>16% Si 92 HBN
HTA Iron
Based Alloys
HTA Cobalt
Based Alloys
HTA Nickel
Based Alloys
HTA Titanium
Based Alloys
Hard Steel
>1400 N/mm2
>415 HBN
Chilled Cast Iron
>1400 N/mm2
>400 HBN
General Purpose End Mills
Note: HTA = High Temperature Alloys
Shoulder Milling / Profiling Feed Correction Parameters
ap ae Correction Factor
ae 0,05 D
0,10 D 2,30 x fz
0,15 D 1,65 x fz
0,20 D 1,40 x fz
0,30 D 1,25 x fz
1,09 x fz
For ae less than ae max, use correction factors stated above.
For ae max, use feeds stated above.
www.kennametal.su B67
для заказа - kennametal@kennametal.su