KMT STELLRAM - полный каталог инструмента - 2014 год EN
B_LL2 / B_XLXL2 для размещения заказа - kennametal@kennametal.su
2 - Flute Ball Nose End Mill
Solid Carbide Recommended Feeds
General Purpose - Eng Milling
B_LL2 / B_XLXL2 Feeds fz (mm/tooth) - Slotting / Pocketing
General Purpose End MillsD
Unalloyed SteelRangeMin. -Min. -Min. -Min. -Min. -Min. -Min. -Min. -Min. -Min. -Min. - Min. - Min. - Min. - Min. - Min. - Min. - Min. - Min. -
<600 N/mm24,0Max.Max.Max.Max.Max.Max.Max.Max.Max.Max. Max. Max. Max. Max. Max. Max. Max. Max. Max.
<180 HBN6,0
8,0 0,012 0,012 0,012 0,012 0,011 0,012 0,012 0,010 0,012 0,012 0,012 - - 0,012 0,009 0,009 0,012 - -
Unalloyed Steel10,00,0200,0200,0200,0190,0170,0190,0170,0150,0200,0190,017 0,020 0,015 0,014 0,019
700-950N/mm212,00,0180,0180,0180,0180,0160,0180,0180,0150,0180,0180,018 - - 0,018 0,013 0,013 0,018 - -
200-280 HBN0,0330,0330,0330,0300,0270,0300,0270,0240,0340,0300,027 0,034 0,025 0,024 0,033
Alloyed Steel0,0240,0240,0240,0240,0210,0240,0240,0200,0240,0240,024 - - 0,024 0,018 0,018 0,024 - -
<600 N/mm20,0490,0490,0490,0430,0370,0430,0370,0330,0510,0430,037 0,051 0,036 0,035 0,047
0,030 0,030 0,030 0,030 0,026 0,030 0,030 0,025 0,030 0,030 0,030 - - 0,030 0,023 0,023 0,030 - -
<180 HBN0,0650,0650,0650,0560,0470,0560,0470,0420,0680,0560,047 0,068 0,049 0,046 0,063
Alloyed Steel0,0360,0360,0360,0360,0300,0360,0360,0300,0360,0360,036-- 0,036 0,029 0,029 0,036 - -
950-1200N/mm20,0820,0820,0820,0700,0570,0700,0570,0510,0870,0700,057 0,087 0,062 0,058 0,079
280-355 HBN
Alloyed Steel
1200-1400N/mm2
355-415 HBN
Stainless Steel
Austenitic + Ferretic
300 Series
Stainless Steel
Martensitic
400 Series
Stainless Steel
Refractory PH
Cast Irons
Grey
GG-FT
Cast Irons
Spheroidal- Ductile
GGG-FGS
Cast Irons
Malleable
GTS -MN/MP
Aluminium &
Alloys
<16% Si 116 HBN
Aluminium & Silicon
>16% Si 92 HBN
HTA Iron
Based Alloys
HTA Cobalt
Based Alloys
HTA Nickel
Based Alloys
HTA Titanium
Based Alloys
Hard Steel
>1400 N/mm2
>415 HBN
Chilled Cast Iron
>1400 N/mm2
>400 HBN
Note: HTA = High Temperature Alloys
Shoulder Milling / Profiling Feed Correction Parameters
ap ae Correction Factor
ae
Note: For copy milling &
shoulder milling applications,
refer to page B90.
B70 www.kennametal.su
для заказа - kennametal@kennametal.su