KMT STELLRAM - полный каталог инструмента - 2014 год EN
для размещения заказа - kennametal@kennametal.su 8000VS45-_R-12
Milling Inserts
SCCT12T-ER SCHT12-TN SCKT12-41 SCMT12-41 SCMT12-T SPHX12-EN dr
l
Product Application & Material Dimensions (mm) Cartridge Face Mills
Roughing Semi-Finishing Finishing s
EDP Item Description Grade Depth of Cut (mm) d (IC) l s r hm min
ap max. ap min. - max. ap min. - max.
7,00
1,00 - 3,50 0,20 -1,00
-
Insert selection with facet
034591 SCCT12M5ACTR X400 12,7 12,7 5,00 Facet 0,15
12,7 12,7 5,00 Facet 0,15
034552 SCCT12M5ACTR SP4019 - 12,7 12,7 5,00 Facet 0,15
017695 SCCT12M5ACTR GH1
017312 SCCT12M5ACER MP91M - 12,7 12,7 5,00 Facet 0,03
017698 SCHT12M5ACTN X500 12,70 12,70 5,00 Facet 0,15
031504 SCHT12M5ACTN SP6519 12,70 12,70 5,00 Facet 0,15
017313 SCHT12M5ACTN MP91M 12,70 12,70 5,00 Facet 0,15
015144 SCKT12M5ACSN-41 X500 - - 12,70 12,70 5,00 Facet 0,12
- - 12,70 12,70 5,00 Facet 0,12
031556 SCKT12M5ACSN-41 SP6519 - - 12,70 12,70 5,00 Facet 0,12
017314 SCKT12M5ACSN-41 MP91M - 12,70 12,70 5,00 1,20 0,06
- 12,70 12,70 5,00 1,20 0,06
Insert selection with corner radius - 12,70 12,70 5,00 1,20 0,06
015226 SCMT12M512EN-41 X500 -
031475 SCMT12M512EN-41 SP6519 -
017317 SCMT12M512EN-41 MP91M -
034554 SCMT12M512T X400 - - 12,70 12,70 5,00 1,20 0,15
0,15
024129 SCMT12M512T X500 - - 12,70 12,70 5,00 1,20 0,15 INSERT APPLICATION NOTES:
0,15 All inserts with a radius should
034555 SCMT12M512T SP6519 - - 12,70 12,70 5,00 1,20 0,15 only be used for semi roughing
applications, where a finished
034553 SCMT12M512T SP4019 - - 12,70 12,70 5,00 1,20 surface is not required.
017316 SCMT12M512T MP91M - - 12,70 12,70 5,00 1,20
Machining Choice: 1st Choice 2nd Choice 3rd Choice | Material Guide Key descriptions found on page A5.
Note: Feed recommendations can be found on page A138. Speed recommendations can be found on page A139.
Product Application & Material Dimensions (mm)
Roughing Semi-Finishing Finishing
EDP Item Description Grade Depth of Cut (mm) d (IC) l s r hm min
ap max. ap min. - max. ap min. - max.
- - 0,20 -1,00
Wiper Inserts
017237 SPHX12M512EN GH1 -- 12,55 12,55 5,00 Wiper 0,02
Facet 0,02
031455 SPHX12M512EN SA9608 -- 12,55 12,55 5,00
Wiper
Facet
Machining Choice: 1st Choice 2nd Choice 3rd Choice | Material Guide Key descriptions found on page A5.
Note: Mounting instruction for wiper inserts refer to page A161.
www.kennametal.su A137
для заказа - kennametal@kennametal.su