Ниже представлена эта же страница в формате, позволяющем производить копирование текста.

KMT STELLRAM - полный каталог инструмента - 2014 год EN

                      8000V                                                    для размещения заказа - kennametal@kennametal.su
                      Mounting / Adjusting Cartridges

Cartridge Face Mills                                                           C Mounting & Setting of the Finishing Cartridges

                                             0,2 mm - 1,0 mm                   The 8000V series of milling cutters have no additional and independent pockets,
                                              1B                               but according to their diameter one, two or even three roughing cartridges can be
                                                                               replaced by one finishing cartridge - 81 FS 00 R-12. One corresponding pocket is
                                                                           1A  marked with an “F”.
                                0,03 mm - 0,05 mm
                      2                                                        NOTE: When using two or even three finishing cartridges, their equal spacing on
                                                                               the milling cutter circumference must be ensured and the axial runout between the
                                                  3                            edges of the wiper inserts must be as small as possible.
                                                      4
                                                                               MOUNTING&SETTINGINSTRUCTIONS
                           5                                                   	 1.	A	 After the 81 FS 00 R-12 cartridge and its pocket in the cutter body have 		
                                                                               		 been cleaned, place the cartridge into its pocket and locate the heel 		
                                                                               			 against the setting track.
                                                                               		B	 Introduce the cartridge fixing screw and lightly tighten. The finishing 		
                                                                               			 inserts will protrude from the cutting plane of the roughing cartridges
                                                                               			 0,2 to 1mm depending upon the roughing inserts being used.
                                                                               	 2.	Check each insert on the roughing cartridges, whose mounting is			
                                                                               		 described in A and B so that the highest insert can be marked and
                                                                               		 used to set the pre-setter to zero.
                                                                               	 3.	A	 Rotate the cutter until the plunger / lens is placed above the centre of the 	
                                                                               			 finishing insert cutting edge.
                                                                               		B	 Screw in the set screw, which will move the 81 FS 00 R-12 finishing 		
                                                                               			 cartridge off the setting track until the measuring system indicates +0,03 to
                                                                               			 0,05 mm from the zero already set. If the roughing cartridges are
                                                                               			 equipped with SCMT utility inserts (with as pressed periphery), the
                                                                               			 offset should only be +0,02mm.
                                                                               		C	 Loosen the cartridge fixing screw and move the cartridge up and down to 	
                                                                               			 verify the dimension already set. If necessary, correct the preset dimension 	
                                                                               		 by adjusting the set screw.
                                                                               	 4.	Lightly tighten the cartridge fixing screw.
                                                                               	 5.	The 81 FS 00 R-12 finishing cartridges are able to be pulled back or pushed 	
                                                                               		 forward as necessary to allow for roughing or finishing work as they will 		
                                                                               		 always return to the dimension as preset in 3 B and C. So, simply unscrew 		
                                                                               		 the fixing screw, push the finishing cartridge either forward or backwards, 		
                                                                               		 then lock the screw again.

                                                                               Note: Not suitable for use on 8010 V cutter bodies.

                      A164                                                                                                       www.kennametal.su

                                                                               для заказа - kennametal@kennametal.su
Заявка