KMT STELLRAM - полный каталог инструмента - 2014 год EN
ER_NN4-with Radius (r) для размещения заказа - kennametal@kennametal.su
4 - Flute End Mill
Solid Carbide Recommended Feeds
General Purpose - Eng Milling
ER_NN4-(r) Feeds fz (mm/tooth) - Shoulder Milling (ae max)
General Purpose End MillsD
Unalloyed SteelRangeMin. -Min. -Min. -Min. -Min. -Min. -Min. -Min. -Min. -Min. -Min. - Min. - Min. - Min. - Min. - Min. - Min. - Min. - Min. -
<600 N/mm23,0Max.Max.Max.Max.Max.Max.Max.Max.Max.Max. Max. Max. Max. Max. Max. Max. Max. Max. Max.
<180 HBN4,00,0090,0090,0090,0090,0090,0090,0090,0070,0090,0090,009 0,009 0,007 0,007 0,009
5,0 0,014 0,014 0,014 0,013 0,012 0,013 0,013 0,011 0,014 0,013 0,012 - - 0,014 0,011 0,010 0,014 - -
Unalloyed Steel6,00,0120,0120,0120,0120,0110,0120,0120,0100,0120,0120,012 - - 0,012 0,009 0,009 0,012 - -
700-950N/mm28,00,0200,0200,0200,0190,0170,0190,0170,0150,0200,0190,017 - - 0,020 0,015 0,014 0,019 - -
200-280 HBN10,00,0150,0150,0150,0150,0130,0150,0150,0130,0150,0150,015 - - 0,015 0,011 0,011 0,015 - -
Alloyed Steel12,00,0270,0270,0270,0250,0220,0240,0220,0190,0270,0250,022 - - 0,027 0,020 0,019 0,026 - -
<600 N/mm216,00,0180,0180,0180,0180,0160,0180,0180,0150,0180,0180,018 - - 0,018 0,013 0,013 0,018 - -
0,033 0,033 0,033 0,030 0,027 0,030 0,027 0,024 0,034 0,030 0,027 - - 0,034 0,025 0,024 0,033 - -
<180 HBN0,0240,0240,0240,0240,0210,0240,0240,0200,0240,0240,024 - - 0,024 0,018 0,018 0,024 - -
Alloyed Steel0,0490,0490,0490,0430,0370,0430,0370,0330,0510,0430,037 0,051 0,036 0,035 0,047
950-1200N/mm20,0300,0300,0300,0300,0260,0300,0300,0250,0300,0300,030 0,030 0,023 0,023 0,030
280-355 HBN0,0650,0650,0650,0560,0470,0560,0470,0420,0680,0560,047 0,068 0,049 0,046 0,063
Alloyed Steel0,0360,0360,0360,0360,0300,0360,0360,0300,0360,0360,0360,0360,0290,029 0,036
1200-1400N/mm20,0820,0820,0820,0700,0570,0700,0570,0510,0870,0700,0570,0870,0620,058 0,079
355-415 HBN0,0480,0480,0480,0480,0390,0480,0480,0400,0480,0480,0480,0480,0390,039 0,048
Stainless Steel0,1190,1190,1190,0990,0790,0990,0790,0700,1270,0990,0790,1270,0900,0840,115
Austenitic + Ferretic
300 Series
Stainless Steel
Martensitic
400 Series
Stainless Steel
Refractory PH
Cast Irons
Grey
GG-FT
Cast Irons
Spheroidal- Ductile
GGG-FGS
Cast Irons
Malleable
GTS -MN/MP
Aluminium &
Alloys
<16% Si 116 HBN
Aluminium & Silicon
>16% Si 92 HBN
HTA Iron
Based Alloys
HTA Cobalt
Based Alloys
HTA Nickel
Based Alloys
HTA Titanium
Based Alloys
Hard Steel
>1400 N/mm2
>415 HBN
Chilled Cast Iron
>1400 N/mm2
>400 HBN
Note: HTA = High Temperature Alloys
Shoulder Milling / Profiling Feed Correction Parameters
ap ae Correction Factor
ae 0,05 D
0,10 D 2,30 x fz
0,15 D 1,65 x fz
0,20 D 1,40 x fz
0,30 D 1,25 x fz
1,09 x fz
For ae less than ae max, use correction factors stated above.
For ae max, use feeds stated above.
B58 www.kennametal.su
для заказа - kennametal@kennametal.su