Ниже представлена эта же страница в формате, позволяющем производить копирование текста.

KMT STELLRAM - полный каталог инструмента - 2014 год EN

                      80.0VR00-_R-20                             для размещения заказа - kennametal@kennametal.su
                      Technical Information

Cartridge Face Mills  Simplified formulas to evaluate hm and fz based on axial depth of cut or radial engagement.

                      Calculation of the average chip thickness in relation with the D.O.C. (Axial)

                      Formula: Programme Feed Rate (fz)          hm	 =	Average chip thickness                      Formula: Average Chip Thickness (hm)
                                                                 ap	 =	Depth of cut
                            fz = hm x           d                fz	 =	Feed per tooth                              hm = fz x                                        ap
                                                ap               d	 = 	Insert diameter                                                                              d

                      Calculation of the average chip thickness in relation with the ae (Radial Engagement) if ae is less than 50% of dia.

                      Formula: Programme Feed Rate (fz)          hm	 =	Average chip thickness                      Formula: Average Chip Thickness (hm)
                                                                 ae	 =	Radial engagement
                            fz = hm x           d                fz	 =	Feed per tooth                              hm = fz x          ae
                                                ae               d	 = 	Cutter diameter                                                d

                      With round inserts,the thickness of the chip varies depending on the axial depth of cut (ap) and is related to the size of the cutting edge-
                      preparation. For best tool life it is important to maintain the proper chip thickness as shown below. This chart calculates in relation with
                      axial depth of cut (ap) only and not radial cut (ae).

                            RD..2006.. Inserts      Insert size  ap d.o.c.           hm (mm)                               fz (mm/Z)
                                      Insert          (mm)        (mm)
                                                                            min. max.                              min. max.
                             RDHT2006M0E-42-X8          20         1,00
                                                        20         2,00     0,08 0,18                              0,36 0,80
                              RDHW2006M0E-X8            20         3,00     0,08 0,18                              0,25 0,57
                                                        20         4,00     0,08 0,18                              0,21 0,46
                              RDHW2006M0S-X8            20         5,00     0,08 0,18                              0,18 0,40
                            RDHW2006M0S-25-X8           20         6,00     0,08 0,18                              0,16 0,36
                                                        20         8,00     0,08 0,18                              0,15 0,33
                                                        20        10,00     0,08 0,18                              0,13 0,28
                                                                            0,08 0,18                              0,11 0,25
                                                        20         1,00
                                                        20         2,00     0,10 0,20                              0,45 0,89
                                                        20         3,00     0,10 0,20                              0,32 0,63
                                                        20         4,00     0,10 0,20                              0,26 0,52
                                                        20         5,00     0,10 0,20                              0,22 0,45
                                                        20         6,00     0,10 0,20                              0,20 0,40
                                                        20         8,00     0,10 0,20                              0,18 0,37
                                                        20        10,00     0,10 0,20                              0,16 0,32
                                                                            0,10 0,20                              0,14 0,28
                                                        20         3,00
                                                        20         4,00     0,15 0,25                              0,39 0,65
                                                        20         5,00     0,15 0,25                              0,34 0,56
                                                        20         6,00     0,15 0,25                              0,30 0,50
                                                        20         8,00     0,15 0,25                              0,27 0,46
                                                                            0,15 0,25                              0,24 0,40
                                                        20         4,00
                                                        20         5,00     0,25 0,30                              0,56 0,67
                                                        20         6,00     0,25 0,30                              0,50 0,60
                                                        20         8,00     0,25 0,30                              0,46 0,55
                                                                            0,25 0,30                              0,40 0,47

                      A160                                                                                                    www.kennametal.su

                                                                 для заказа - kennametal@kennametal.su
Заявка