7702VRD & 7712VRD Series для размещения заказа - kennametal@kennametal.su
Technical Information
With round inserts, the thickness of the chip varies depending on the axial depth of cut.
For best tool-life it is important to maintain the proper chip thickness as shown below.
Contour Mills Inserts RD..0702...
Dimensions (mm)
Inserts Insert ap hm hm fz fz
Geometry Size Axial d.o.c. min. max. min. max.
E-701 7,00 0,10 0,02 0,06 0,17 0,50
7,00 0,25 0,02 0,06 0,11 0,32
T 7,00 0,50 0,02 0,06 0,07 0,22
7,00 0,75 0,02 0,06 0,06 0,18
7,00 1,00 0,02 0,06 0,05 0,16
7,00 1,25 0,02 0,06 0,05 0,14
7,00 1,30 0,02 0,06 0,05 0,14
7,00 0,10 0,05 0,08 0,42 0,67
7,00 0,25 0,05 0,08 0,26 042
7,00 0,50 0,05 0,08 0,19 0,30
7,00 0,75 0,05 0,08 0,15 0,24
7,00 1,00 0,05 0,08 0,13 0,21
7,00 1,25 0,05 0,08 0,12 0,19
7,00 1,30 0,05 0,08 0,12 0,19
With round inserts, the thickness of the chip varies depending on the axial depth of cut.
For best tool-life it is important to maintain the proper chip thickness as shown below.
Inserts RD..1003..
Dimensions (mm)
Inserts Insert ap hm hm fz fz
Geometry Size Axial d.o.c. min. max. min. max.
E-701 10,00 0,10 0,04 0,07 0,40 0,70
T 10,00 0,25 0,04 0,07 0,25 0,44
10,00 0,50 0,04 0,07 0,18 0,31
10,00 0,75 0,04 0,07 0,15 0,26
10,00 1,00 0,04 0,07 0,13 0,22
10,00 1,25 0,04 0,07 0,11 0,20
10,00 1,50 0,04 0,07 0,10 0,18
10,00 1,75 0,04 0,07 0,10 0,17
10,00 2,00 0,04 0,07 0,09 0,16
10,00 2,25 0,04 0,07 0,08 0,15
10,00 2,50 0,04 0,07 0,08 0,14
10,00 0,10 0,10 0,15 1,00 1,50
10,00 0,25 0,10 0,15 0,63 0,95
10,00 0,50 0,10 0,15 0,45 0,67
10,00 0,75 0,10 0,15 0,37 0,55
10,00 1,00 0,10 0,15 0,32 0,47
10,00 1,25 0,10 0,15 0,28 0,42
10,00 1,50 0,10 0,15 0,26 0,39
10,00 1,75 0,10 0,15 0,24 0,36
10,00 2,00 0,10 0,15 0,22 0,34
10,00 2,25 0,10 0,15 0,21 0,32
10,00 2,50 0,10 0,15 0,20 0,30
A228 www.kennametal.su
для заказа - kennametal@kennametal.su